Aruba AP-303 (RW) Unified Access Point 802.11ac Wave2 Dual-Band 867/300Mbps

Product Specification

Overview

HPE Aruba AP-303 (RW) (JZ320A) Unified Wireless Access Point 802.11ac Wave 2 Dual-Band 867/300Mbps

Unified AP – deploy with or without controller
Dual Radio 2x2 802.11ac access point with Multi-User MIMO (wave 2)
Built-in Bluetooth Low-Energy (BLE) radio
Advanced Cellular Coexistence (ACC)
Quality of service for unified communications applications
RF Management
Spectrum analysis

อุปกรณ์รองรับ POE (Not include Adpter)

WI-FI RADIO SPECIFICATIONS

AP type: Indoor, dual radio, 5GHz 802.11ac 2x2 MIMO and 2.4GHz 802.11n 2x2 MIMO

• 5GHz (radio 0):
  • Two spatial stream Single User (SU) MIMO for up to 867Mbps wireless data rate to individual 2SS VHT80 client devices
  • Two spatial stream Multi User (MU) MIMO for up to 867Mbps wireless data rate to two 1SS MU-MIMO capable client devices simultaneously
• 2.4GHz (radio 1):
  • Two spatial stream Single User (SU) MIMO for up to 300Mbps wireless data rate to individual 2SS HT40 client devices

Support for up to 256 associated client devices per radio, and up to 16 BSSIDs per radio

Supported frequency bands (country-specific restrictions apply):

2.400 to 2.4835GHz
5.150 to 5.250GHz
5.250 to 5.350GHz
5.470 to 5.725GHz
5.725 to 5.850GHz 

Available channels: Dependent on configured regulatory domain

Dynamic frequency selection (DFS) optimizes the use of available RF spectrum

Supported radio technologies:

802.11b: Direct-sequence spread-spectrum (DSSS)
802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM)

Supported modulation types:

802.11b: BPSK, QPSK, CCK
802.11a/g/n/ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM

Transmit power:

Configurable in increments of 0.5dBm

Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements):

2.4GHz band: +21dBm (18dBm per chain)
5GHz band: +21dBm (18dBm per chain)
Note: conducted transmit power levels exclude antenna gain. For total (EIRP) transmit power, add antenna gain

Advanced Cellular Coexistence (ACC) minimizes the impact of interference from cellular networks
Maximum ratio combining (MRC) for improved receiver performance
Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance
Short guard interval for 20MHz, 40MHz and 80MHz channels
Space-time block coding (STBC) for increased range and improved  reception
Low-density parity check (LDPC) for high-efficiency error correction  and  increased throughput
Transmit beam-forming (TxBF) for increased signal reliability and range

Supported data rates (Mbps):

802.11b: 1, 2, 5.5, 11
802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
802.11n: 6.5 to 300 (MCS0 to MCS15)
802.11ac: 6.5 to 867 (MCS0 to MCS9, NSS = 1 to 2)
802.11n high-throughput (HT) support: HT20/40
802.11ac very high throughput (VHT) support: VHT20/40/80
802.11n/ac packet aggregation: A-MPDU, A-MSDU

WI-FI ANTENNAS

The antennas are optimized for horizontal ceiling mounted orientation of the AP. The downtilt angle for maximum gain is roughly 30 degrees.

Combining the patterns of both antennas per radio, the peak gain of the average (effective) pattern is 2.1dBi in 2.4GHz and 4.6dBi in 5GHz.

OTHER INTERFACES

• E0: One 10/100/1000BASE-T Ethernet network interface (RJ-45)
  • Auto-sensing link speed and MDI/MDX
  • POE-PD: 48Vdc (nominal) 802.3af POE
• E1 (AP-303P models only): One 10/100/1000BASE-T
• Radio status - Zigbee 802.15.4 radio (AP-303P models only)
• DC power interface, accepts 2.1/5.5-mm center-positive circular plug with 9.5-mm length
• Bluetooth Low Energy (BLE) radio
  • Up to 3dBm transmit power (class 2) and -93dBm receive sensitivity
  • Integrated vertically polarized omnidirectional antenna with roughly 30 degrees downtilt and peak gain of 4.5dBi
• Visual indicators (tri-color LEDs): for System and Radio status
• Reset button: factory reset (during device power-up), LED mode control (normal/off)
• Serial console interface (proprietary, µUSB physical jack)
• Kensington security slot

POWER SOURCES AND CONSUMPTION

The AP supports direct DC power and Power over Ethernet (PoE)

• • When both power sources are available, DC power takes priority over PoE
  • Power sources are sold separately

AP-303 models: (อุปกรณ์รองรับไฟผ่าน POE หากไม่มี Switch POE ต้องซื้อ Power Injection หรือ Adapterเพิ่ม)

• • Direct DC source: 12Vdc nominal, +/- 5%
  • DC power interface accepts 2.1/5.5-mm center-positive circular plug with 9.5-mm length
  • Power over Ethernet (PoE): 48Vdc (nominal) 802.3af compliant source
  • Maximum (worst-case) power consumption: 10.1W (PoE) or 8.8W (DC)
  • Maximum (worst-case) power consumption in idle mode: 4.2W (PoE) or 4.0W (DC)

AP-303P models:

• • Direct DC source: 48Vdc nominal, +/- 5%
  • DC power interface accepts 1.35/3.5-mm center-positive circular plug with 9.5-mm length
  • Power over Ethernet (PoE-PD) on E0: 48Vdc (nominal) 802.3af/at/bt compliant source
  • PoE-PSE function on E1 disabled when powered by 802.3af PoE
  • Maximum (worst-case) power consumption: 11.3 (PoE) or 11.5 (DC)
  • Maximum (worst-case) power consumption in idle mode: 6.8 (PoE) or 7.0 (DC)
  • Power consumption numbers exclude power to support PoE-PSE function on E1

MOUNTING

The AP ships with a (black) mount clips to attach to a 9/16-inch or 15/16-inch flat T-bar drop-tile ceiling.

Several optional mount kits are available to attach the AP to a variety of surfaces; see the Ordering Information section below for details.

MECHANICAL

Dimensions and weight (unit, excluding mount accessories):

• • 150mm (W) x 150mm (D) x 35mm (H) or 5.9" (W) x 5.9" (D) x 1.4" (H)
  • 260g or 9.2oz

Dimensions and weight (shipping):

• • 190mm (W) x 180mm (D) x 60mm (H) or 7.4" (W) x 7.0" (D) x 2.4" (H)
  • 410g or 14.5oz

ENVIRONMENTAL

Operating:

• • Temperature: 0° C to +40° C (+32° F to +104° F)
  • Humidity: 5% to 93% non-condensing

Storage and transportation:

• • Temperature: -40° C to +70° C (-40° F to +158° F)

REGULATORY

FCC/ISED
CE Marked
RED Directive 2014/53/EU
EMC Directive 2014/30/EU
Low Voltage Directive 2014/35/EU
UL/IEC/EN 60950
EN 60601-1-1 and EN 60601-1-2

RELIABILITY

MTBF: 795khrs (91yrs) at +25C operating temperature

CERTIFICATIONS

CB Scheme Safety, cTUVus
UL2043 plenum rating
Wi-Fi Alliance (WFA) certified 802.11a/b/g/n/ac
Passpoint® (Release 2) with ArubaOS and Instant 8.3+

MINIMUM SOFTWARE VERSIONS

AP-303 models: ArubaOS & Aruba InstantOS 8.3.0.0
AP-303P models: ArubaOS & Aruba InstantOS 8.4.0.0 

Warranty

Life Time Carry-in Warranty by HPE Thailand (5 ปีหลังเลิกผลิต)